Electronics

Relay module specifications:

1. Input voltage: 5V DC – pins DC+, DC-, IN

2. Relay load capacity

- 10A 250VAC

- 10A 125VAC

- 10A 30VDC

- 10A 28VDC

3. Rated consumption: up to 200mA

4. Standby consumption: 10mA

5. Mounting holes: 4 holes, 3mm

The board offers individual control of two electromagnetic relays, with load circuits of 10A at 250V. The control pins are isolated by optocouplers, ensuring high safety and guaranteeing that no spikes will appear in the control electronics. The board is powered by supplying 5V to DC+ and GND to DC-. The control pin levels are 5V tolerant. The control pins are driven by active high/low voltage, set by jumpers S1 and S2. Position H sets active high voltage, and position L sets active low voltage. The relay interfaces have normally open circuits. All three relay outputs are brought out to the output terminal – normally closed, common, and normally open, marked as NC, COM and NO.

Board specifications:

• Supply voltage: 4 AA batteries, approx. 6V

• Compatibility with UNO R3: Mounting holes

• Wheel diameter: 67mm

• Module height: 34mm

• Electric motor parameters:
  • Soldered cables + and –

  • Bidirectional movement

  • Gear ratio: 48:1

  • Speed: approx. 0.65m/s

  • Recommended supply voltage: 5 - 10V

  • Current consumption: 100mA/3V, 120mA/6V

  • Dimensions: ~215mm x ~150mm

Arduino compatible BLDC Shield allows Arduino Uno and other compatible boards to be used to control brushless DC electric motors.

Board specifications:

• Input voltage: 5V USB or 7-12V on pin VIN
• Connector types: MINI-USB-B
• Microcontroller: ATmega328P-AU – 8-bit, 16MHz frequency
• Flash memory: 32 kb
• EEPROM memory: 1 kb
• 2 kb SRAM memory
• 8 analogue inputs: A0-A7, 10-bit ADC
• 14 digital input/output pins: 6 of which are PWM
• Maximum allowable current per input/output pin: 20 mA
• Chip for USB communication: CH340, interface USB to Serial
• Dimensions: 45 mm x 18 mm
• Weight: 0.026 kg

Board specifications:

• Input voltage: 5V USB or 7-12VDC input jack
• Connector types: USB-B or DC connector 5.5x2.1mm
• Microcontroller: ATmega328P-AU – 8-bit, 16MHz frequency
• Flash memory: 32kb
• EEPROM memory: 1kb
• 2kb SRAM memory
• 6 analog inputs: A0-A10, 10-bit ADC
• 14 digital input/output pins: 6 of which are PWM
• Maximum allowable current per input/output pin: 20mA
• Chip for USB communication: CH340G USB to UART chip
• Dimensions: 73mm x 54mm x 17mm
• Weight: 0.026 kg

Board specifications:

• Supply voltage: 3.3V or 5V supplied by the Arduino board via the pin headers

• Compatibility with UNO R3: Pin headers on the bottom layer of the board

• Compatibility with MEGA2560: Pin headers on the bottom layer of the board

• Buttons: 6 push buttons connected to the pin header, corresponding to digital pins D2-D7, built-in joystick button connected to D8

• Joystick: two-axis joystick providing proportional voltage to analog pins A0 and A1

• Slide switch button: for selecting the voltage supplied to connected additional devices

• Additional devices: socket headers for nRF24L01 WIFI transmitter and 5110 LCD screen
• Additional communication pins: SDA and SCL from the I2C communication and TX/RX for connecting devices via UART.

Supported axes: 6

Interface: USB

Maximum pulse signal frequency: up to ~200 kHz

Supply voltage: 12-32V

MPG (Handwheel) support: Yes

Supported software: Mach3

General-purpose opto-isolated output port: 10 pcs

General-purpose opto-isolated input port: 12 pcs

Spindle port: 0-10V (can also be used as PWM output)

Supply voltage: 12-32V

Motor type: Stepper motors – direction and step control (Pulse/Dir)

Applications: CNC routers, mini mills, engraving machines, automation

Weight: 0.350 kg.

Technical specifications:

Model: HT-GE134GC-T1P-C

- Interface: Gigabit Ethernet (RJ-45)

- Lens mount: C-mount

- I/O: 6-pin circular connector – power, Trigger In, Strobe/Output

- Resolution (series "134"): approx. 1.3 MP (e.g. 1280×1024)

- Frame rate: up to ~30 fps (depending on settings)

- Power supply: 12–24 VDC via 6-pin connector

- Software/SDK: compatible with GigE camera platforms (e.g. GigE Vision/GenICam)

- Housing: metal, with mounting threads

Package includes:

- Industrial camera HT-GE134GC-T1P-C

- Power + I/O cable

Technical specifications:

- Input voltage: 5 – 30V DC

- Output voltage: 0.5 – 30V DC

- Output current: up to 4A (recommended: up to 3.5A for continuous operation)

- Maximum power: 50W (recommended: up to 35W)

- Operating modes:

- Constant Voltage (CV)

- Constant Current (CC)

- Dimensions: 79 x 43 x 26 mm

- Weight: 0.090 kg

Converter specifications:

- Input voltage: 4.5V - 28V DC

- Output voltage: 0.8V – 20V DC, adjustable via potentiometer

- Rated output current: up to 1.8A

- Maximum output current: 3A, cooling heatsink required

- Quiescent current: 100uA

- Efficiency: up to 96%

- Operating frequency: up to 1.5MHz, but depends on the value set by the resistors on the board

- Output voltage ripple: 30mV

- Built-in protections: output short-circuit protection, thermal protection

- Operating temperature: -14 - +50 °C

- Dimensions: 22x17x4mm

Technical specifications:

Input voltage: 6V – 40V DC

Output voltage: 1.2V – 36V DC (adjustable)

Maximum output current: 20A

Recommended continuous current: up to 15A

Maximum power: 300W

Efficiency: up to 95%

Switching frequency: 180kHz

Output ripple: ≤50mV

Dimensions: 62 × 53 × 27 mm

Weight: 0.085 kg.